A Brief Guide on Using Electric Paint Sprayer on House Exterior

Painting procedure needs some specific tools to complete the task. No matter what either you are using a roller, brush, roller, or sprayer, everything  is having its own advantage or disadvantage. But when things are right, painting your hose using a sprayer will be easier and will end the work soon as compared to roller or brush.

How to spray paint a house interior? In the following blog, we will be looking at the different aspect related to the electric paint sprayer. Let’s get started:


This completes the task fast. Once you have completed the preparation. The sprayer is primed and the task is done quickly. This provides better coverage. This is the best option if your house is not having a perfectly flat or have obstacles like pipes, slats, clapboard, etc.

If you are planning to give your house exterior a perfect finish, then you should hire the exterior painters Cape Cod to get satisfactory results. The professionals will be using the right equipment to execute the work and will tell you about the high-quality paint for your house.


The preparation work takes time. You have to mask all other things in the spraying range that you are not going to paint.

Even after doing the proper masking you have to clean the paint. You approximately need 30 minutes to clean the paint sprayer properly.

Materials and Tools Needed

The different tools and house spray painting equipment that you will need are listed below:

Paint: You can select any according to your own choice. You need to ensure that it is an exterior paint. Furthermore, if you are planning to end the job soon, then you should buy 5-gallon paint cans.

Airless Paint Sprayer: You will need an airless paint sprayer that will directly draw from can instead of filling up an attached can.

Clean Water Bucket: A buck of clean water that will remain clean throughout the entire process.

Waste Bucket: This bucket will receive drained paint and other deposits of the painting process.

Setting of Sprayer in Paint Cans and Bucket

It is important to note that all sprayers are different. For placing various tubes into bucking, following is a general guide for the help:

Drain in Waste: You have to put the drain tube into the waste bucket.

Siphon in Paint: Siphon is a large tube with a wire screen at the end. You have to place it directly inside the paint can with screened-end at the bottom.

Plug-in Power: Plugin sprayer to the electrical supply.

Remember that you have to place the paint and bucket side by side.

Priming the Sprayer

You will have a single switch that is having prime and paint modes. You have to switch to prime. Next, you need to turn on the paint sprayer and hold the spray trigger.

Instantly Move Drain Tube to Your Paint Can

For your information, the pump will run for 30 seconds. The paint will pump out from the paint can through the sprayer machine and exit drain tube into the waste bucket. Next, you have to quickly switch to the drain tube by placing it to the paint can toward the bottom. Note that there might be clips that will hold drain and siphon tubes together. After this, your paint will be on a continuous path.

If you want quick switching, then it is better to keep buckets side by side.

Wear Maximum Protection Before Spraying

You should be wearing protective gear before you start the spraying process. You have to protect your eyes, hair, skin, and clothes. Some of the protective gears are listed below:

Googles: You should not only use the safety glasses but prefer to use goggles that cover your eyes properly.

Full-body coveralls: You should buy one with booties attached. If not, then you should buy shoe covers.

Spray Sock: If your coverall is not having an attached hood, then you should buy a spray sock. It is just a simple piece of cloth with a face cut out.

Gloves: You should use some old gloves or latex gloves. But remember that latex gloves may get slippery after a certain period.

Keep Paint Spray Gun 12″ to 24″ Away from Wall

If you are going to hold the spray gun closer than 12”, then this will result in drips. Contrarily, when you are holding the gun far than 24”, then this will result in uneven coverage.

Create Sections When Spraying Paint

When you are using a paint sprayer on your house exterior, it is similar to using a large version of a paintbrush. The roles played are same. It is better to divide your work into sections and use best paint sprayer for exterior house. You should finish one section first and then move to the next section.

The sections should be small enough that edges stay wet and you should move from one section to another.

Keep Spray Gun Parallel to the Wall

It is written in the paint sprayer instruction book to keep the spray gun parallel to the wall during the entire process. The professionals will follow this step.

If the work is not done by the professionals, then the gun will angle away mostly at the end of the run. The best you can do is to minimize the tilts and you should cover bad edges on the next run.

Place Siphon Tube in Clean Water and Flush Out Sprayer

Once you are done, then you should fill the clean bucket with water. You should remove the siphon tube from the can of paint and put it to the clean bucket. You need to switch the paint machine to prime or flush. You should spray until you get the clean water out. You have to change the water in a clean bucket three times to get clean water out.

Be the first to comment on "A Brief Guide on Using Electric Paint Sprayer on House Exterior"

Leave a comment